INTERPHASE CORPORATION V/ATM 5215 NIC Type ATM (OC-3c) Processor Motorola 68EC040 Processor Speed 20/25MHz Maximum Onboard Memory 512KB SRAM/4MB SRAM Cache 1024KB SRAM I/O Options Serial port (exact location and function unidentified) Boot ROM Not available Network Transfer Rate 155Mbps Topology Unidentified Wire Type Fiber optic cable Data Bus VME double [Image] CONNECTIONS Function Label Function Label Fiber optic transmit CN1 Fiber optic receive CN2 cable connector cable connector USER CONFIGURABLE SETTINGS Setting Label Position » Power-on self-test enabled JA1 Open Power-on self-test disabled JA1 Closed » XON/XOFF flow control disabled JA2 Open XON/XOFF flow control enabled JA2 Closed » Factory configured - do not alter JA3 Open » Factory configured - do not alter JA4 Open » Factory configured - do not alter JA5 Open » Serial port speed is 38.4K00bps JA6 Open Serial port speed is 9600bps JA6 Closed » Processor speed is 25MHz JA7 Open Processor speed is 20MHz JA7 Closed » Cache enabled JA8 Open Cache disabled JA8 Closed » Factory configured - do not alter JA9 Open » Factory configured - do not alter JA10 Open » Serial port disabled JA11 Open Serial port enabled JA11 Closed » GDB debug mode disabled JA12 Open GDB debug mode enabled JA12 Closed » DTACK signal not filtered JA13 Closed DTACK signal filtered JA13 Open » Card will request VME bus even when JA14 Open its request level is unavailable Card will not request VME bus until JA14 Closed its request level is available » Card will use standard release mode JA15 Open for releasing the VME bus Card will use early release mode for JA15 Closed releasing the VME bus » Short I/O size is 512 bytes JA18 Closed Short I/O size is 2048 bytes JA18 Open » VRAM buffer not accessible to VME A24 JA19 Closed space VRAM buffer is accessible to VME A24 JA19 Open space » VRAM allows non-privileged or JA20 Closed privileged address modifiers VRAM allows privileged address JA20 Open modifiers only » Factory configured - do not alter JA21 Open » Factory configured - do not alter JA22 Open Short I/O compare circuitry to accept JA23 Open only privileged address modifiers Short I/O compare circuitry to accept JA23 Closed both privileged and non-privileged address modifiers. Note:The manufacturer suggests that JA18 remain closed. Not all boards may support VRAM buffer access in VME A24 space (jumper JA19). Contact the manufacturer for more information. If jumpers JA16 and JA17 are installed on your board they should remain open. INTERRUPT REQUEST PRIORITY SELECTION Setting BR0 BR1 BR2 BR3 0 1 & 2, 3 & 4 & 5 4 & 5 4 & 5 4, 5 & 6 1 4 & 5 1 & 2, 3 & 4 & 5 4 & 5 4, 5 & 6 2 4 & 5 4 & 5 1 & 2, 3 & 4 & 5 4, 5 & 6 3 4 & 5 4 & 5 4 & 5 1 & 2, 3 & 4, 5 & 6 Note:Pins designated are in the closed position. SHORT I/O BASE ADDRESS SELECTION Setting JA24 JA25 JA26 JA27 JA28 JA29 JA30 0000h Closed Closed Closed Closed Closed Closed Closed 0200h Closed Closed Closed Closed Closed Closed Open 0400h Closed Closed Closed Closed Closed Open Closed 0600h Closed Closed Closed Closed Closed Open Open 0800h Closed Open Open Closed Closed Closed Closed » 6000h Closed Open Open Closed Closed Closed Closed F600h Open Open Open Open Closed Open Open F800h Open Open Open Open Open Closed Closed FA00h Open Open Open Open Open Closed Open FC00h Open Open Open Open Open Open Closed FE00h Open Open Open Open Open Open Open Note: A total of 128 base address settings are available. The jumpers are a binary representation of the decimal memory addresses. JA24 is the Most Significant Bit and jumper JA30 is the Least Significant Bit. The jumpers have the following decimal values: JA24=32768, JA25=16384, JA26=8192, JA27=4096, JA28=2048, JA29=1024, JA30=512. Open the jumpers and add the values of the jumpers that are open to obtain the correct memory address. (Open=1, Closed=0) DIAGNOSTIC LED(S) LED1 LED1 LED5 LED6 LED7 Condition Color Status Status Status Status Red On Blinking Off Off Memory diagnostic test failed Red On Off Blinking Off DMA diagnostic test failed Red On Blinking Blinking Off FE diagnostic test failed Red On Off Off On Firmware panic condition occurred Red On On Off On VME bus error occurred Red On Off On On VME bus timeout occurred Red On Blinking Blinking Blinking Power-on reset in progress Red On On On On Power-on reset in progress Green On Blinking Blinking Blinking Common Boot Interface ready Green On Cycle Cycle Cycle Adapter is active N/A Off N/A N/A N/A Power is off or board is improperly installed DIAGNOSTIC LED(S) (CON'T) LED Color Status Condition LED2 Unidentified On Board is accessing SRAM LED2 Unidentified Off Board is not accessing SRAM LED3 Unidentified On Board is accessing VRAM LED3 Unidentified Off Board is not accessing VRAM LED4 Unidentified On VME bus is performing DMA transfer to board LED4 Unidentified Off VME bus is not performing DMA transfer to board DBLED1 Green On Network connection is good DBLED1 Green Off Network connection is broken DBLED2 Yellow On Power-on reset in progress DBLED2 Yellow Blinking Daughterboard is initialized and functioning DBLED2 Yellow Off Power-on reset complete Note:The term 'Cycle' in reference to LED5-LED7 indicated that the LEDs are turning on in sequence, one after the other. The colors of LED5-LED7 are unidentified. DBLED1 and DBLED2 are on the daughterboard.